Sales hotline+86 135 1772 8899 | EmailQL8899@hotmail.com | WhatsApp+86 135 1772 8899
Genset HubDIESEL POWER · CHINA

Diesel generator maintenance: what a proper service actually covers

A standby genset that has not run under load for six months is not a backup — it is a gamble. This page sets out the service intervals we use on 20–4000 kVA sets, the work included at each interval, what a maintenance contract should contain, and how we support sets shipped outside China.

Service intervals that follow the engine, not the calendar

Interval is driven by running hours first and time second. A standby set that runs 30 hours a year still needs an annual service, because oil oxidises, fuel degrades and batteries sulphate whether the engine turns or not. A prime-power set running 12 hours a day will reach 500 hours in six weeks.

IntervalTriggerCore work
First service50 h or 1 monthBreak-in oil and filter change, retorque critical fasteners, check valve clearance, record baseline
Routine AEvery 250 h or 6 monthsOil and oil filter, drain water from fuel pre-filter, air filter restriction reading, belt tension, coolant level and condition, battery voltage and specific gravity
Routine BEvery 500 h or 12 monthsAll of Routine A plus fuel filter replacement, fuel/water separator, crankcase breather, inspect radiator fins and charge-air hoses, generator bearing listen, insulation resistance (megger) test
Major serviceEvery 2000 h or 24 monthsValve clearance adjustment, injector test, turbo boost and end-float check, cooling system flush, AVR and governor calibration, full load bank test with report

These are the base intervals for Yuchai, Weichai, Cummins and Perkins platforms. Severe duty — dusty quarry air, ambient above 45 °C, high sulphur fuel — halves the oil and filter interval. If your site is in that category, say so when ordering the kit; it changes what we ship.

What people forget between services

The failures we are called out for are rarely wear-related. They are storage and readiness problems, and they do not show up on an hour meter.

Three contract shapes

1. Per-visit service

You call, we come. Suitable for a single standby set that runs a few hundred hours a year and has a competent on-site technician for weekly checks. You pay labour plus parts per visit.

2. Annual package (two visits)

The usual choice for hospitals, hotels, data rooms and factories. Two scheduled visits a year covering Routine A and Routine B, consumables included, plus one emergency call-out. For a 100 kVA set this typically starts around USD 800 per year ex-works Liuzhou, and scales with rating, site distance and whether the set is parallel-capable.

3. Full maintenance contract

Fixed annual fee covering scheduled service, all wear parts, fault diagnosis and repair labour, with a response-time commitment. Preferred where the genset protects revenue — cold chain, broadcasting, continuous process plant — and where the owner has no in-house mechanical staff.

What the contract should actually promise

Vague contracts are the norm and they are worth little. Four clauses decide whether the contract has teeth:

ClauseWeak wordingWording that protects you
Response time"Prompt attendance"Remote diagnosis within 2 working hours; technician on site within 4 hours in Liuzhou, 24 hours elsewhere in Guangxi
Parts"Genuine parts where available"Named consumable list included in the fee; non-consumable parts at cost plus a stated margin
Proof of work"Service carried out"Signed checklist per visit plus oil sample result and a load test printout at the annual visit
Uptime"Best efforts"Availability target with a defined credit if a scheduled visit is missed

Support for sets outside China

Roughly two thirds of the sets we ship leave the country, so the maintenance model has to work without us on the ground. It runs on four parts:

  1. Documentation at handover. Operation manual, wiring diagram, controller parameter list, factory load test sheet and a parts book with exploded views — all in English, all specific to the serial number.
  2. Remote diagnosis. Controller event logs and photos or short video over WhatsApp or WeChat. Most no-start and shutdown faults resolve this way inside one working day.
  3. Spare parts kits. A two-year consumables kit shipped with the set: filters, belts, sensors, AVR, water pump seal. Air freight from Liuzhou for anything else, typically 5–8 days.
  4. Local partner training. If you have a service company in your market, we train their technicians on the platform — controller navigation, valve clearance, injector timing — either at our workshop or on your site during commissioning.

Commissioning is part of the service, not an extra

A set that arrives and is simply connected to the load will fail early. Commissioning covers: foundation and anti-vibration check, exhaust back-pressure measurement, coolant and oil verification, fuel line priming and air bleed, phase rotation and voltage checks, governor and AVR setting against your load profile, protection relay calibration, and a stepped load test to nameplate with the results recorded. We issue a commissioning report you can hand to your insurer or your client.

Tell us the rating and the site, and we will quote a service scope

Send the model, serial number, running hours and a photo of the control panel. We reply with a service scope and a fixed price — within two working hours, GMT+8.

Request a service quotation See model list

Questions buyers ask

Can we service the set ourselves and still keep the warranty?

Yes, if the work is recorded. Keep the hour meter log, the filter part numbers and the oil grade used, and have the annual visit done by an authorised technician. Warranty disputes almost always come down to missing records, not to who turned the spanner.

How often should a standby set be load tested?

Annually at minimum, with a written report. If the set protects a hospital, data room or cold store, test quarterly at 50 % and 100 % load for 30 minutes each. A set that only ever runs at 10 % load will wet-stack and lose capacity.

What does a spare parts kit contain?

For a typical 200 kVA set: 4 oil filters, 4 fuel filters, 2 water separators, 1 air filter, 1 belt set, 1 water pump seal kit, 1 AVR, 1 speed sensor and a thermostat. Sized for two years of standby duty. We list every part number against your engine serial before shipping.

Do you handle sets you did not supply?

Yes. We service Cummins, Perkins, Deutz, Volvo Penta and Chinese platforms including Yuchai and Weichai, and we will tell you honestly when a repair is not economic. For sets over 15 years old with unavailable parts, we usually recommend a replacement study rather than an open-ended repair.

Related: diesel generator prices and cost breakdown · silent canopy gensets · containerized power modules · all diesel generator sets 8–4000 kVA